Firmware 2.6.0.3

These release notes document the differences between the OCPP Native implementation on Zaptec Go and the official OCPP 1.6 specification as described by OCA with errata v4.0. Any aspect of the OCPP implementation that diverges from the OCA specification is unintentional and may be corrected in the future. Please inform Zaptec of any such divergencies. In addition to any previous release notes:

Changes since previous release

Fixed issue where reconnection attempt on LTE would cause OCPP to restart, stopping ongoing transaction, instead of normal offline to online transition.
Fixed an issue when attempting to start a transaction from Finishing.
Fixed an issue where attempts to reconnect due to a disconnect would not be stopped after switching away from OCPP mode.

Firmware 2.5.1.0

These release notes, document the differences between the OCPP Native implementation on
Zaptec Go and the official OCPP 1.6 specification as described by OCA with errata v4.0. Any
aspect of the OCPP implementation that diverges from the OCA specification is unintentional
and may be corrected in the future. Please inform Zaptec of any such divergencies. In addition to
any previous release notes:

Changes since previous release

Added most of OCPP 1.6 Security Whitepaper (3rd edition) including SecurityProfile 2 &
SecurityProfile 3
Improved reliability of ClockAlignedDataInterval
Re-enabled diagnostics log
Improved transaction start in SuspendedEVSE state
Changed AuthorizationKey validation to use the hex-decoded variant in the Auth header
by default
Added UseAuthorizationKeyWithoutDecoding configuration key to allow backwards
compatibility with previous implementation of AuthorizationKey
Implemented OCPP whitepaper "OCPP & UK Electric Vehicles (Smart Charge Points)
Regulations 2021"
Improved reliability for transaction related messages

OCPP security (whitepaper edition 3)

Added most of OCPP 1.6 Security Whitepaper (3rd edition) including SecurityProfile 2 &
SecurityProfile 3
Added configuration key for SecurityProfile
Added configuration key for AuthorizationKey

OCPP security (whitepaper edition 3) limitations

SecurityProfile 1 may connect to wss:// but will not check the CS(MS) identity via the
certificate. It will only use the protocol and send basic auth.
SignedFirmwareStatusNotification is not supported
SignedUpdateFirmware is not supported

OCPP & UK Electric Vehicles (Smart Charge Points) Regulations 2021 (v1.0)

Added RandomisedDelay configuration keys
Added default TxDefaultProfile for stack level 1 and 2, according to the whitepaper, for
chargers that have a non-OCPP schedule installed when OCPP Native is enabled. The
non-OCPP schedule could have been installed on chargers via the Zaptec app. It is
Installed when the user or installer select "United kingdom" as the location of the
charger without disabling "Set up schedule"

New Zaptec OCPP Native extensions

Configuration key UseAuthorizationKeyWithoutDecoding is by default set to false if
AuthorizationKey has not been set prior to the introduction of this configuration key,
otherwise it will default to true. When false, the charger will attempt to decode the hex-
encoded AuthorizationKey before setting the configuration or using it as the password in
the http basic auth header. It Will also reject any AuthorizationKey that has an invalid
hex-encoding or contains CTL characters or ':' when decoded (see RFC 7617 and
appendix of RFC 5234). When set to true, it will use the possibly hex-encoded
AuthorizationKey directly as the basic auth header password. It will attempt the same
validation as when set to false, but will perform the validation without attempting
decoding and require a longer key

Firmware 2.4.2.4

These release notes document the differences between the OCPP Native implementation on Zaptec Go and the official OCPP 1.6 specification as described by OCA with errata v4.0. In addition to any previous release notes:

Changes since previous release

Fixed issue where a charger would behave as if it had never before connected to the central system after a reboot instead of behaving as if offline until reconnected.
Added configuration key “PowerActiveImportDeltaForEagerMeterValueSample”
Fixed issue where TriggerMessage.req with invalid connector id would ignore the id.
Improved state transition where Finishing would be unnecessary.
Fixed an issue during failed reset attempts.
Improved error notifications.
Fixed a rare issue where messages were never sent.

New Zaptec OCPP Native extentions

Configuration key PowerActiveImportDeltaForEagerMeterValueSample allows the charger to sample and report the next Sample.Periodic early if the difference in Power.Active.Import exceed the configured value. The configured value is represented in Watts.

Firmware 2.4.1.8

These release notes document the differences between the OCPP Native implementation on Zaptec Go and the official OCPP 1.6 specification as described by OCA with errata v4.0. In addition to any previous release notes:

Changes since previous release

Fixed an issue where ClearProfile.req incorrectly clears TxDefaultProfile instead of MaxProfile
Fixed incorrect transition to SuspendedEV from SuspendedEVSE
Fixed an issue with handeling messages while offline
Improved WeakSignal detection and reporting
Fixed issue where ChargingProfiles was applied incorrectly
Fixed state transition after ConnectionTimeout
Improved status notification for connector 0
Fixed SupportedFeatureProfiles value being incorrect

OCPP Core profile

All features and configurations are implemented and adhere to errata v4.0 if not otherwise specified.
When the number of meter values exceed the amount specified in StopTransactionMaxMeterValues, the charger will remove intermediate messages. It will start by removing the first message that is not sampled as Transaction.Begin, and procede by removing every other message (3th, 5th etc) until the amount of meter values is less than or equal to StopTransactionMaxMeterValues. It will not delete the message that is sampled as Transaction.End.
When the charger is configured to allow local authorization and the charger has an idTag that is not accepted, it will send an Authorize.req to check if the idTagInfo has been updated. The charger will also do this if there is a possibility that the parentIdTag has been added or changed when comparing tags. This may result in an Authorize.req for both keys being compared. This behaviour is not expected by OCTT and may be removed in future versions.
The charger may send a new BootNotification.req after attempting reconnect when the CS(MS) sends a websocket close frame. If the charger goes offline without getting a close frame, then it will not send a new BootNotification.req.
The charger will deny any charging services and stay disabled (indicated by main LED being off) if it has never before been accepted by the CS(MS) with the current connection settings. Connection settings in this context are currently the CS(MS) URL and charger ID. SecurityProfile related configurations are currently not considered connection settings in this context. This may change in a future version.
The charger will stop ongoing transactions after er reset due to PowerLoss. It will not send the StopTransaction.req before the reset.

Zaptec OCPP Native extensions

Configuration key FreeChargingIdTag allows setting a default idTag that will be sent if no other idTag is known.
Configuration key FreeCharging allows charging to start automatically without presenting an idTag or RemoteStartTransaction.req
Configuration key LockCablePermanently allows the charger to present as if the cable is permanently attached.
Configuration keys specified outside of OCPP 1.6 such as MeterValuesSignatureContexts, StopTransactionSignatureContexts and StopTransactionSignatureFormat mentioned in OCMF are not supported

Firmware 2.4.1.0

These release notes document the initial release version of the firmware with OCPP native capabilities. Any aspect of the OCPP implementation that diverges from the specification of OCPP 1.6 edition 2 with JSON and errata up to version v4.0 is unintentional and may be corrected in the future. Please inform Zaptec of any such divergencies.

Known issues

DiagnosticsStatus may be incorrect and misleading if diagnostics log has not been enabled by Zaptec on the specific charger.
CP may not reconnect automatically after CS(MS) sends a specific disconnect event without acknowledging chargers' response within 1 second.
When switching from OCPP Cloud mode to OCPP Native mode, inconsistency can be observed between the total kWh meter value reported by the charger and the sum of all previous OCPP session kWh values. This can occur, for example, if the charger was previously operated on occasion outside the OCPP reporting infrastructure. Where there is a discrepancy, the total kWh meter value reported in OCPP Native mode should be considered accurate, as it is taken directly from the charger's built-in energy meter.

Changes since previous release

Various changes related to handling of filesystem.
Various changes related to standalone mode.
Added configuration key “FreeCharging” to allow charging without presenting RFID-Token or remoteStartTransaction.
Added configuration key “FreeChargingIdTag” used as a token when charger is set to allow charging without authorisation.
Added configuration key “LockCablePermanently” to simulate Chargepoint with “Fixed cable“. When set to true, UnlockCableOnEVSideDisconnect will show as false in a GetConfiguration request and read-only as suggested for chargers with “Fixed cable” in OCPP errata v4.0. When changed back to false, UnlockConnectorOnEVSideDisconnect will show as having its original value in a GetConfiguration request and can be altered with ChangeConfiguration.
Changes relevant for users of pre-release version: renamed custom Configuration keys to be consistent with existing OCPP Bridge at portal.zaptec.com

OCPP Core profile

All required operations and configuration keys are supported
Authorization cache is supported
Configuration key MessageTimeout specified in errata v4.0 is supported
Configuration key StopTransactionMaxMeterValues specified in errata v4.0 is supported
Optional Configuration key AllowOfflineTxForUnknownId is supported
Optional Configuration key AuthorizationCacheEnabled is supported
Optional Configuration key ConnectorPhaseRotationMaxLength is supported
Optional Configuration key LightIntensity is supported
Optional Configuration key MeterValuesAlignedDataMaxLength is supported
Optional Configuration key MeterValuesSampledDataMaxLength is supported
Optional Configuration key MinimumStatusDuration is supported
Optional Configuration key StopTxnAlignedDataMaxLength is supported
Optional Configuration key StopTxnSampledDataMaxLength is supported
Optional Configuration key SupportedFeatureProfilesMaxLength is supported

OCPP Core profile limitations

Configuration for BlinkRepeat is not supported
Configuration for MaxEnergyOnInvalidId is not supported
Configuration keys specified outside of OCPP such as MeterValuesSignatureContexts, StopTransactionSignatureContexts and StopTransactionSignatureFormat mentioned in OCMF are not supported
Meter values are always sent as raw
Sampled meter value and heartbeat intervals can be set to any number between 0 and 4294967 It has been tested with short intervals and no issue has been observed with 1 second intervals, but this has not been tested with high load or poor network connectivity. Some measurands are sampled at close to 1 second interval and the meter value may therefore be up to approximately 1 second old when sent with OCPP. We do not recommend short meter value intervals.
Configuration key for StopTransactionOnEVSideDisconnect is set to true and not write protected, but can only be set to true by CS. This is to conform to OCPP specification 1.6 prior to errata v4.0
CP clock is synchronized with NTP and not CS.
CP expects CS to use timestamp in UTC
Some optional parameters for BootNotification.req (meterSerialNumber, meterType) is not sent and others (iccid, imsi) may only be sent when LTE has been used prior to bootnotification and after last reset
MeterValues are not measured from EV, cable or grid locations
Only a few measurands are supported: Current.Import, Current.Offered, Energy.Active.Import.Register, Energy.Active.Import.Interval, Temperature, Voltage
CP does not have Emergency stop button
StatusNotifications that were generated and not sent before CP detected offline will not be deleted and may be sent after CP re-connects. StatusNotification for state transition while offline will be sent with timestamp for when CP came online.
StatusNotifications with errors will not be queued when offline.
Transaction related messages are prioritised if they can be sent, even if they were queued when offline. This may cause other messages to be delayed after a re-connect with many queued transaction related messages.

OCPP Firmware Management profile

All required operations and configuration keys are supported
Configuration key SupportedFileTransferProtocols specified in errata v4.0 is supported
Diagnostics upload uses http(s) and form upload

OCPP Firmware Management profile limitations

FTP(s) is not supported
Diagnostics log must be enabled by zaptec on individual device for it to be available and work as expected.

OCPP Local Auth List Management profile

All required operations and configuration keys are supported
Authorization list is set to allow 1024 entries and allow 255 entries in a single SendLocalList operation

OCPP Reservation profile

All operations and configuration keys are supported

OCPP Reservation profile limitations

If Authorization is set to not required, then active reservations will be cancelled and new reservations will be rejected until authorization is set to required.

OCPP Smart Charging profile

All required operations and configuration keys are supported

OCPP Smart Charging profile limitations

Configuration for ConnectorSwitch3to1PhaseSupported is not supported
Only 'A' is allowed as ChargingRateUnitType
startSchedule is required on recurring schedules

OCPP Remote Trigger profile

All operations are supported

OCPP security (whitepaper edition 3)

Added configuration key for SecurityProfile
Added configuration key for AuthorizationKey

OCPP security (whitepaper edition 3) limitations

SecurityProfile can only be set to 0 or 1.
SecurityProfile 1 may connect to wss:// but will not check the CS(MS) identity via the certificate. It will only use the protocol and send basic auth.
Configuration for AdditionalRootCertificateCheck is not supported
Configuration for CertificateSignedMaxChainSize is not supported
Configuration for CertificateStoreMaxLength is not supported
Configuration for CpoName is not supported
CertificateSigned is not supported
DeleteCertificate is not supported
ExtendedTriggerMessage is not supported
GetInstalledCertificateIds is not supported
GetLog is not supported
InstallCertificate is not supported
LogStatusNotification is not supported
SecurityEventNotification is not supported
SignCertificate is not supported
SignedFirmwareStatusNotification is not supported
SignedUpdateFirmware is not supported

Zaptec power management

Zaptec power management is not supported

Zaptec app

Older versions of the Zaptec app may display a warning that the charging station is in Standalone mode when OCPP native mode is enabled. This warning can be safely ignored.
In newer versions of the Zaptec app, charging stations in OCPP native mode will not appear in the Zaptec app dashboard

Firmware 2.4.0.2

Known issues

A rare issue may cause a reset to fail.
A charging station may not transition to faulted in a state that prevents charging and signal fault via red LED.
DiagnosticsStatus may be sent as status Uploaded when diagnostics log has not been requested without the feature having been enabled by Zaptec.
A rare issue may cause a crash at an hourly synchronization event under specific circumstances. It is believed to only happen when SmartCharging profile requests the CP to change from/to SuspendedEV very often.
CP may not reconnect automatically after CS(MS) sends specific disconnect event.

OCPP Core profile

All required operations and configuration keys are supported
Authorization cache is supported
Configuration key MessageTimeout specified in errata v4.0 is supported
Configuration key StopTransactionMaxMeterValues specified in errata v4.0 is supported
Optional Configuration key AllowOfflineTxForUnknownId is supported
Optional Configuration key AuthorizationCacheEnabled is supported
Optional Configuration key ConnectorPhaseRotationMaxLength is supported
Optional Configuration key LightIntensity is supported
Optional Configuration key MeterValuesAlignedDataMaxLength is supported
Optional Configuration key MeterValuesSampledDataMaxLength is supported
Optional Configuration key MinimumStatusDuration is supported
Optional Configuration key StopTxnAlignedDataMaxLength is supported
Optional Configuration key StopTxnSampledDataMaxLength is supported
Optional Configuration key SupportedFeatureProfilesMaxLength is supported

OCPP Core profile limitations

Configuration for BlinkRepeat is not supported
Configuration for MaxEnergyOnInvalidId is not supported
Configuration keys specified outside of OCPP such as MeterValuesSignatureContexts, StopTransactionSignatureContexts, and StopTransactionSignatureFormat mentioned in OCMF are not supported
Meter values are always sent as raw
Meter value intervals can be set to any number between 0 and UINT32_T. It has been tested with short intervals and no issue has been observed with 1-second intervals, but this has not been tested with high load or poor network connectivity. Some measurands are sampled at close to 1-second intervals and the meter value may therefore be up to approximately 1 second old when sent with OCPP.
Configuration key for StopTransactionOnEVSideDisconnect is set to true and not write protected, but can only be set to true by CS. This is to conform to OCPP specification 1.6 prior to errata v4.0
CP clock is synchronised with NTP and not CS.
CP expects CS to use timestamp in UTC
Some optional parameters for BootNotification.req (meterSerialNumber, meterType) is not sent and others (iccid, imsi) may only be sent when LTE has been used before boot notification and after last reset
MeterValues are not measured from EV, cable, or grid locations
Only a few measurands are supported: Current. Import, Current.Offered, Energy.Active.Import.Register, Energy.Active.Import.Interval, Temperature, Voltage
CP does not have an Emergency stop button
StatusNotifications that were generated and not sent before CP detected offline will not be deleted and may be sent after CP re-connects. StatusNotification for state transition while offline will be sent with timestamp for when CP came online.
StatusNotifications with errors will not be queued when offline.

OCPP Firmware Management profile

All required operations and configuration keys are supported
Configuration key SupportedFileTransferProtocols specified in errata v4.0 is supported
Diagnostics upload uses http(s) and form upload

OCPP Firmware Management profile limitations

FTP(s) is not supported
Diagnostics log must be enabled by Zaptec on specific devices for it to be available
We do not distribute firmware files; all firmware updates are provided by the Zaptec cloud

OCPP Local Auth List Management profile

All required operations and configuration keys are supported
Authorisation list is set to allow 1024 entries and 255 entries in a single SendLocalList operation

OCPP Reservation profile

All operations and configuration keys are supported

OCPP Reservation profile limitations

If Authorisation is set to not required, then active reservations will be canceled and new reservations will be rejected until authorisation is set to required.

OCPP Smart Charging profile

All required operations and configuration keys are supported

OCPP Smart Charging profile limitations

Configuration for ConnectorSwitch3to1PhaseSupported is not supported

OCPP Remote Trigger profile

All operations are supported

OCPP security (whitepaper edition 3)

Added configuration key for SecurityProfile
Added configuration key for AuthorisationKey

OCPP security (whitepaper edition 3) limitations

SecurityProfile can only be set to 0 or 1.
SecurityProfile 1 may connect to wss:// but will not check the CS(MS) identity via the certificate. It will only use the protocol and send basic auth.
Configuration for AdditionalRootCertificateCheck is not supported
Configuration for CertificateSignedMaxChainSize is not supported
Configuration for CertificateStoreMaxLength is not supported
Configuration for CpoName is not supported
CertificateSigned is not supported
DeleteCertificate is not supported
ExtendedTriggerMessage is not supported
GetInstalledCertificateIds is not supported
GetLog is not supported
InstallCertificate is not supported
LogStatusNotification is not supported
SecurityEventNotification is not supported
SignCertificate is not supported
SignedFirmwareStatusNotification is not supported
SignedUpdateFirmware is not supported

Zaptec power management

Zaptec power management is not supported.

Zaptec app

Older versions of the Zaptec app may display a warning that the charging station is in Standalone mode when OCPP native mode is enabled. This warning can be safely ignored.
In newer versions of the Zaptec app, charging stations in OCPP native mode will not appear in the Zaptec app dashboard.

Changelog